can finally say i'm an AMD User again...

[plonk420]

just got a 2400G!

temps are a bit high, though. like REALLY high (not sure if default cooler is a bit wonky). like 90, 94C was the highest i saw them get. ended up undervolting 0.15V (couldn't hit 0.2V). this got temps down to 75C or so.

the 30 mins i spent with the GPU was pretty nifty, too.

any idea if CPU performance is affected by running single channel? DDR4 is soooo freakin' expensive currently.

[Dirk Broer]

DDR4 is soooo freakin' expensive currently.

I noticed that when I bought my A12-9800E and bought 16GB DDR4 to go with it, the RAM was just as expensive as the CPU/APU and the mobo (Asrock A320M Pro4) combined!
90-94℃ seems too high to me, check whether the cooler makes good contact with the CPU/APU.
Running your RAM in single channel-mode will halve the maximum theoretical memory bandwidth (which is why I ended up buying two sticks of 8GB, instead of one of 16GB).

[plonk420]

90-94℃ seems too high to me, check whether the cooler makes good contact with the CPU/APU.

Running your RAM in single channel-mode will halve the maximum theoretical memory bandwidth (which is why I ended up buying two sticks of 8GB, instead of one of 16GB).

yeah, i wanted 2 x 2GB, but it seems 4GB is the smallest desktop RAM makers are manufacturing...

and i reeeeally don't want to check HSF contact... will have to take entire mobo out

i'm pretty chuffed at power consumption, tho. 32 watts at idle (i7-4790 from Lenovo was 29 watts). after the undervolting, the distributed computing load consumption was 84 watts. the i7 was 105 give or take. and that even went up to 135 watts or so with a GTX 1060 installed.

[Dirk Broer]

90-94℃ seems too high to me, check whether the cooler makes good contact with the CPU/APU.

I hate to be an I-told-you-so, but...

[SuicideCabbage]

I was determined to get Threadripper this year, still may, but 99% sure I am going to wait after I discovered 4GB per thread would run me $1,800...

[Dirk Broer]

I was determined to get Threadripper this year, still may, but 99% sure I am going to wait after I discovered 4GB per thread would run me $1,800...

4GB/thread with a 32-core threadripper means a whopping 128GB of RAM in eight sticks of 16GB. Somewhat surprisingly this can be bought -as cheapest solution- in the form of eight sticks of
Corsair Dominator Platinum CMD128GX4M8B2800C14 at € 1.129,- (interngeheugen.com)
If you prefer ECC RAM you can do with four 32GB sticks for around € 1.600 Euro. This might come in handy when future threadrippers will have even more cores...present threadripper mobo's do not support more than 128GB though, IIRC.

[Nflight]

Ouch too Hot for me, Ouch to costly for me, if only I was rich

[Jason1478963]

I have been trying the Corsair H60's on my ryzen setups

[plonk420]

I have been trying the Corsair H60's on my ryzen setups

if it'll fit around your RAM, check out the Scythe Ninja 4 ($34-40 + $5 AM4 adapter kit) or FSP Windale 6 ($43). while there's no direct comparison of H60 to Ninja 4 or Windale (in my quick google), the NH-D15 beats the H60 by a degree at Guru3D. and the Ninja 4 is hotter than the D15 by 0.25C at TweakTown. and the Windale equals the D15 except when OC'd where it's just hotter by 1C.

unless you're going for small space consumption around the CPU, in which case the H60 wins easily :D

i did a quick vid showing how easy the Ninja 4 install was on AM4... and a side note: the RAM i installed in slot 2 last night cleared by under 5mm. i forgot to pay attention to vertical clearance, so i can't remember if it's completely under the cooler or not (no heatsink like the RAM in the video as it's the same model)

edit: ah yes, the heatsinkless RAM appears to fit under in my video

[SuicideCabbage]

I wanted to go ECC, and here in the states the price difference between non-ECC and ECC is only $60-80 for the 128GB set, so that's a no brainer to go ECC. Still though, with the PSU, mobo, chip, water (or possibly oil immersion), RAM, and 6x GPUs, even going used on the GPUs (speced for crunching not mining, so not stupidly overpriced but still high) the build is in the ballpark of $7,000.

At this point I am really leaning on phasing out a 3.7Ghz OC quad with a 5-5.2Ghz OC oct, and calling it a year. I need to make my final decision soon however, as the Pentathlon is drawing near. That being said, crunchers in the field, what is the real-life throughput of the Ryzen vs the FX-9590 oct (at stock or low 5s)? Used FX-9590 is $100-150, and all I would need is the chip, so unless the Ryzen's are ridiculously better, it's not worth an entire build on the AM4 platform. I am a fan of go big or go home, if the AM4 build is ~$1,000 and at least doubles the FX I'll go that route, else I will just phase out the quad and wait until next year to talk myself into the then best in slot TR4.